Accessoires en PVC Elevate

PVC Split Pipe Boot

Elevate PVC Split Pipe Boots are factory-fabricated flashings made from high-performance Elevate PVC with DuPont Elvaloy® KEE roofing membrane. The split boot is specifically designed for flashing round penetrations of various sizes from 1" to 12" (25 mm to 305 mm). The split tab design allows the boot to be used for flash pipe penetrations with limited or no access from above the penetration. This pipe boot design eliminates the need to field fabricate with PVC Unsupported Flashing, thus lessening labor and increasing the performance of the system.

PVC Universal Pipe Flashings

Elevate PVC Universal Pipe Flashings are factory-fabricated flashings made from high-performance Elevate PVC with DuPont Elvaloy® KEE roofing membrane. The universal boot is specifically designed for the flashing of round penetrations. PVC Universal Pipe Flashing fits various penetrations from 1" (25 mm) to 4½" (114,3 mm). The Elevate PVC Universal Pipe Flashing must be cut to correct size before installation..

PVC T-Joint Covers

Elevate PVC T-Joint Covers are a flexible, non-reinforced, flashing membrane made with DuPont Elvaloy® KEE. They are designed to cover and seal T-joints formed at seam intersections and angle changes 1:12 or greater for Elevate PVC reinforced membranes..

PVC Inside and Outside Molded Corners

Elevate PVC Inside and Outside Molded Corners are made with non-reinforced Dupont Elvaloy® KEE. The PVC Inside and Outside Molded Corners were specifically designed for flashing inside and outside corners on curbs, parapets, scuppers, and other areas where an inside or outside factory formed corner flashing is appropriate..

PVC 8" Cover Strip

Elevate PVC 8" Cover Strip is a pre-cut 8" (203 mm) wide cover strip made from 60 mils (1,5 mm) thick, reinforced Elevate PVC membrane. This heat weldable cover strip can be used as a cover for intermediate or perimeter mechanical attachment on PVC systems as well as for stripping in PVC Coated Metal roof edge details and Elevate PVC XR membrane end laps.

Unsupported PVC Flashing

Elevate PVC Unsupported Flashing is a non-reinforced PVC membrane made with DuPont Elvaloy® KEE, used in roofing applications where Elevate pre-formed PVC accessory products are not appropriate. Elevate PVC Unsupported Flashing is available in 50' (15,2 m) rolls..

PVC X-Tred Walkway Pad

The Elevate PVC X-Tred Walkway Pad is a highly specialized UV resistant pad made from PVC and designed to provide protection from essential rooftop services and traffic and maintain the integrity of the existing roof surface. PVC X-Tred Walkway Pads can be installed loose-laid on top of the existing PVC adhered roof assembly, making installation simple

PVC Walkway Pad

The Elevate PVC Walkway Pad is a reinforced thermoplastic material intended for use as a traffic bearing surface over Elevate PVC roofing installations. The pad is produced in 30" (762 mm) wide by 60' (18,3 m) long rolls; gray in color or safety yellow to highlight traffic and maintenance pathways. The pad has a textured top surface and a smooth bottom surface for easy welding to the Elevate PVC roof membrane

Jet double

Twin Jet is a two-component, low-rise polyurethane adhesive applied in bead pattern for the attachment of Elevate approved roof insulations. It may also be used in bead or spatter pattern for the attachment of Elevate PVC XR membrane to acceptable horizontal substrates, per Elevate specifications. Twin Jet is packaged in portable pressurized canisters, allowing extrusion of Part 1 and Part 2 to the gun and mix tip assembly.

Jet Bond PVC

Elevate Jet Bond PVC is a Low VOC sprayable bonding adhesive designed for portability and easeof-use. C’est un produit polyvalent qui nécessite un temps d’évaporation minimal. Jet Bond PVC adheres standard PVC membranes to multiple substrates. Il est parfait pour les couvreurs qui cherchent une solution de rechange plus pratique que les applications traditionnelles à rouler.